Westinghouse WGR050NG076 Dokumentacja

WHL-001 REV. 12.17.14 High Efficiency Water Heater INSTALLATIO

10 WHL-001 REV. 12.17.14  Location that could cause the system

11 WHL-001 REV. 12.17.14  When raising the heater, fully suppor

12 WHL-001 REV. 12.17.14 If the confined space is within a build

13 WHL-001 REV. 12.17.14 determine if there is blockage, leakage,

14 WHL-001 REV. 12.17.14 Total Dissolved Solids Total Dissolve

15 WHL-001 REV. 12.17.14 Figure 3 – *ALL DIMENSIONS ARE APPROXIM

16 WHL-001 REV. 12.17.14 PERFORMANCE SPECIFICATIONS FOR HIGH EFFI

17 WHL-001 REV. 12.17.14 B. SCALDING This heater can deliver sca

18 WHL-001 REV. 12.17.14 preventers on all incoming water supplie

19 WHL-001 REV. 12.17.14 The water heater must be full of water

2 WHL-001 REV. 12.17.14 IF THE INFORMATION IN THIS MANUAL IS NO

20 WHL-001 REV. 12.17.14 J. PIPING DIAGRAMS Figure 4 – High Effi

21 WHL-001 REV. 12.17.14 Figure 5 – High Efficiency Water Heate

22 WHL-001 REV. 12.17.14 Figure 6 – High Efficiency Water Heater

23 WHL-001 REV. 12.17.14 PART 5 – VENTING, COMBUSTION AIR AND CON

24 WHL-001 REV. 12.17.14 B. APPROVED MATERIALS FOR EXHAUST VENT A

25 WHL-001 REV. 12.17.14 You must not use “B” vent in an exhaust

26 WHL-001 REV. 12.17.14 The building owner is responsible for

27 WHL-001 REV. 12.17.14 G. EXHAUST VENT AND INTAKE PIPE INSTALLA

28 WHL-001 REV. 12.17.14 When installing a combustion air intake

29 WHL-001 REV. 12.17.14 Figure 9 – Venting with Optional Kits (

3 WHL-001 REV. 12.17.14 The following defined terms are used th

30 WHL-001 REV. 12.17.14 Figure 10 – NOTE: This drawing is meant

31 WHL-001 REV. 12.17.14 Figure 11 – Horizontal Venting - NOTE:

32 WHL-001 REV. 12.17.14 Do not install the heater into a common

33 WHL-001 REV. 12.17.14 3. INDOOR COMBUSTION AIR INSTALLATION I

34 WHL-001 REV. 12.17.14 Figure 14

35 WHL-001 REV. 12.17.14 I. CONDENSATE REMOVAL SYSTEM NOTE: Check

36 WHL-001 REV. 12.17.14 Figure 16 – Removing and Installing the

37 WHL-001 REV. 12.17.14 PART 6 – WIRING A. LINE VOLTAGE INPUT T

38 WHL-001 REV. 12.17.14 Label all wires prior to disconnecting

39 WHL-001 REV. 12.17.14 The gas supply shall have a maximum inl

4 WHL-001 REV. 12.17.14 In Canada – CGA No. B149 (latest version)

40 WHL-001 REV. 12.17.14 It is recommended that a soapy solution

41 WHL-001 REV. 12.17.14 PART 8 – CONTROLS A. CONTROL AND DISPLAY

42 WHL-001 REV. 12.17.14 ECO Mode Putting the water heater into

43 WHL-001 REV. 12.17.14 4. CHANGING USER SETPOINT Press either

44 WHL-001 REV. 12.17.14 To enter Installer Mode, press and hol

45 WHL-001 REV. 12.17.14 1. Connect the outdoor sensor to the t

46 WHL-001 REV. 12.17.14 To enter Installer Mode, press and hold

47 WHL-001 REV. 12.17.14 PART 9 – START-UP PROCEDURE FOR YOUR OW

48 WHL-001 REV. 12.17.14 Test mode can be used to incrementally i

49 WHL-001 REV. 12.17.14 PART 10 – SHUTDOWN A. SHUTDOWN PROCEDURE

5 WHL-001 REV. 12.17.14 PART 5 – VENTING, COMBUSTION AIR AND COND

50 WHL-001 REV. 12.17.14 3. Press the key to clear the fault an

51 WHL-001 REV. 12.17.14 CONTROL BOARD LOCKOUT FAULTS CODE SHORT

52 WHL-001 REV. 12.17.14 Table 18 – Lockout Fault Codes – NOTE: I

53 WHL-001 REV. 12.17.14 Figure 25 – Replacement Parts

54 WHL-001 REV. 12.17.14 Figure 26 – Replacement Parts

55 WHL-001 REV. 12.17.14 PART 12 - MAINTENANCE In unusually dirt

56 WHL-001 REV. 12.17.14 Spark Electrode Clean. Set gap at ¼”. Cl

57 WHL-001 REV. 12.17.14

58 WHL-001 REV. 12.17.14

59 WHL-001 REV. 12.17.14 MAINTENANCE NOTES

6 WHL-001 REV. 12.17.14 D. IMPORTANT NOTICE ...

60 WHL-001 REV. 12.17.14 CUSTOMER INSTALLATION RECORD FORM T

7 WHL-001 REV. 12.17.14 C. GAS Should overheating or gas supply f

8 WHL-001 REV. 12.17.14 Modulating Combustion System Modulation

9 WHL-001 REV. 12.17.14 PART 3 – PREPARE WATER HEATER LOCATION C